overview

TRUDESIGN T Connector 1 1/2" BSP M.F.F - 90893 (138736)

High Tensile and Impact Strength - Free from Corrosion and Electrolysis

Ability to retrofit to existing TruDesign assemblies

Designed and made in New Zealand for use in marine applications above and below the water line, TruDesign Load Bearing Collars are designed for use with TruDesign Skin Fittings and Ball Valves.
With the Collar in place, the Skin Fitting-Ball Valve-Hose Tail assembly will withstand a 500 lb (227 kg) static force applied to the Hose Tail end of the assembly, for a minimum of 30 seconds – complying with North American ABYC H-27 standards.

Note: TruDesign 2" Skin Fittings meet the requirements of H-27 as standard (i.e. without a Large Collar installed). Adding a Large Collar to assemblies of this size increases the overall strength and protects the vulnerable exposed section of thread on the Skin Fitting.

Glass reinforced nylon composite construction

• Light weight and high strength
• Corrosion resistance
  • Long life
  • Minimal maintenance
  • No corrosion deposits to remove
• Electrically non conductive
  • No electrical bonding
  • Suitable for use on all hull types - aluminium, steel, wood or FRP hulls
• UV resistant
  • Will not break down in the sun
• Chemical resistant
  • Impervious to diesel, petrol, oil and antifouling paints
• Large operating temperature range
  • -40° to 80°C (-40° to 176°F)

PTFE enhanced sealing and sliding elements

• Reduced friction for easy operation
• Reduction in blockages due to fouling

High quality

• Quality materials from accredited suppliers
• Standards approved through IMCI to ISO standard 9093-2
• Every Ball Valve is leak tested during manufacture

Standards:

Tru-Design Ball Valves are certified by the International Marine Certification Institute (IMCI) to meet;

• ISO 9093-2 Small craft -- Seacocks and through-hull fittings -- Part 2: Non-metallic

In meeting ISO 9093-2, our Ball Valves have been tested with a 155kg load hanging off a hose fitting while connected to our Skin Fitting.

The locking feature allows the Ball Valve to comply with US Coast Guard Regulation 33 CFR 159.7 and ISO Standard 8099 for locking of toilet waste outlets.

Options:

• 90246 - 13mm Tail Straight Long Thread ½” BSP
• 90875 - 16mm Unequal Tail Straight Long Thread ½” BSP
• 90252 - 19mm Tail Straight Long Thread ¾” BSP
• 90879 - 22mm Unequal Tail Straight Long Thread ¾” BSP
• 90263 - 25mm Tail Straight Long Thread 1” BSP
• 90640 - 28mm Unequal Tail Straight Long Thread 1” BSP
• 90285 - 32mm Tail Straight Long Thread 1¼” BSP
• 90530 - 38mm Unequal Tail Straight Long Thread 1¼” BSP
• 90284 - 32mm Unequal Tail Straight Long Thread 1½” BSP
• 90231 - 38mm Tail Straight Long Thread 1½” BSP
• 90518 - 50mm Tail Straight Long Thread 2” BSP
• Truedesign Ball Valves
• Truedesign Ball Valves - Monitored
• Truedesign Load Bearing Collars
• Truedesign Skin Fittings - Straight
• Truedesign Skin Fittings - Tapered
• Truedesign Hose Tails and T Pieces
• Truedesign Accessories

Downloads:

• TRUDESIGN T-Piece Connector Product Information Sheet

specification